AL8805
Application Information
AL8805 Operation
In normal operation, when voltage is applied at +V IN , the AL8805 internal switch is turned on. Current starts to flow through sense resistor R 1 ,
inductor L1, and the LEDs. The current ramps up linearly, and the ramp rate is determined by the input voltage +Vin and the inductor L1.
This rising current produces a voltage ramp across R 1 . The internal circuit of the AL8805 senses the voltage across R 1 and applies a proportional
voltage to the input of the internal comparator.
When this voltage reaches an internally set upper threshold, the internal switch is turned off. The inductor current continues to flow through R 1 ,
L1, the LEDs and the schottky diode D1, and back to the supply rail, but it decays, with the rate of decay determined by the forward voltage drop
of the LEDs and the schottky diode.
This decaying current produces a falling voltage at R 1 , which is sensed by the AL8805. A voltage proportional to the sense voltage across R 1 is
applied at the input of the internal comparator. When this voltage falls to the internally set lower threshold, the internal switch is turned on again.
This switch-on-and-off cycle continues to provide the average LED current set by the sense resistor R 1 .
LED Current Control
The LED current is controlled by the resistor R 1 in Figure 30.
Connected between V IN and SET the nominal average output current in the LED(s) is defined as:
I LED =
V THD
R SET
If the CTRL pin is driven by an external voltage (higher than 0.4V and lower than 2.5V), the average LED current is:
I LED =
V CTRL V THD
V REF R SET
For example for a desired LED current of 660mA and a default voltage V CTRL =2.5V the resulting resistor is:
R SET =
V THD V CTRL
I LED V REF
=
0 . 1 2 . 5
0 . 66 2 . 5
≈ 150 m Ω
V IN
CTRL
SET
R 1
D 1
C 1
AL8805
C 2
GND
L 1
SW
Figure 30 Typical Application Circuit
DC Dimming
The CTRL pin can be driven by an external DC voltage (V CTRL ), to adjust the output current to a value below the nominal average value defined
by RSET. The LED current decreases linearly with the CTRL voltage when 0.5V ≤ V CTRL ≤ 2.5V, as in Figure 2 for 4 different current levels.
When the CTRL voltage falls below the threshold, 0.4V, the output switch is turned off which allows PWM dimming.
Note that 100% brightness setting corresponds to V CTRL = V REF , nominally 2.5V. For any voltage applied on the CTRL pin that is higher than V REF ,
the device will not overdrive the LED current and will still set the current according to the equation V CTRL = V REF .
AL8805
Document number: DS35030 Rev. 4 - 2
9 of 16
www.diodes.com
July 2012
? Diodes Incorporated
相关PDF资料
AL8806MP8-13 IC LED DVR CONS CURR 8MSOP
AL8807W5-7 IC LED DRVR DCDC BUCK SOT25
AL9910AS-13 IC LED DRVR HIGH BRIGHT SO8EP
ALC60481R05 PWR SUP AC-DC 6-48V 1.05A 50.4W
ALV100362R5 POWER SUPPLY AC-DC 36V 2.5A 90W
ALV60361R7 POWER SUPPLY AC-DC 36V 1.7A 61W
ALV80126R5 POWER SUPPLY AC-DC 12V 6.5A 78W
AOZ1083CI IC LED DRVR BUCK CC 1.2A SOT23-6
相关代理商/技术参数
AL8806 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:HIGH EFFICIENCY 30V 1.5A BUCK LED DRIVER
AL8806EV1 功能描述:AL8806 1, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:1.5A 输出和类型:1,非隔离 电压 - 输出:- 特性:可调光 电压 - 输入:9 V ~ 30 V 所含物品:板 使用的 IC/零件:AL8806 标准包装:1
AL8806EV4 功能描述:AL8806 1, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:1.5A 输出和类型:1,非隔离 电压 - 输出:- 特性:可调光 电压 - 输入:9 V ~ 30 V 所含物品:板 使用的 IC/零件:AL8806 标准包装:1
AL8806EV6 制造商:Diodes Incorporated 功能描述:AL8806 Series 1.5A 30 V 1 MHz SMT Buck LED Driver DC-DC Converter Eval-Board
AL8806M8P-13 功能描述:LED照明驱动器 HIGH EFF 30V 1.5A 6V TO 30V 8 LED RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
AL8806MP8-13 功能描述:LED显示驱动器 HIGH EFF 30V 1.5A 6V TO 30V 8 LED RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
AL8806QMP-13 功能描述:LED 驱动器 IC 1 输出 DC DC 稳压器 降压(降压) 模拟,PWM 调光 1.5A(开关) 8-MSOP-EP 制造商:diodes incorporated 系列:汽车级,AEC-Q100 包装:剪切带(CT) 零件状态:有效 类型:DC DC 稳压器 拓扑:降压(降压) 内部开关:是 输出数:1 电压 - 供电(最低):6V 电压 -?供电(最高):30V 电压 - 输出:36V 电流 - 输出/通道:1.5A(开关) 频率:1MHz 调光:模拟,PWM 应用:汽车级 工作温度:-40°C ~ 125°C (TJ) 安装类型:表面贴装 封装/外壳:8-TSSOP,8-MSOP(0.118",3.00mm 宽)裸焊盘 供应商器件封装:8-MSOP-EP 标准包装:1
AL8807 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:HIGH EFFICIENCY LOW EMI 36V 1A BUCK LED DRIVER